Boeing B737NG - Flight controls

During an ALL FLAPS UP LANDING, the speed to be maintained is:

VREF40 + 60

VREF40 + 15

VREF40 + 55

VREF40 + 30

Correct! Wrong!

The ALTERNATE FLAPS Master Switch:

Fully extends the LE Devices using Standby Hydraulic pressure, and electrically extends the TE Flaps

Activates the Standby Hydraulic Pump and pressurizes the STANDBY Rudder Power Control Unit.

Arms the Alternate Flaps Position Switch, activates the Standby Hydraulic Pump, and closes the Trailing

Closes the Flight Spoiler Shutoff valve

Correct! Wrong!

To operate the Feel system, the Elevator Feel Computer uses:

Hydraulics system B

Either hydraulics system A or B pressure (whichever is higher)

Either hydraulics system A or B pressure

Hydraulics system A

Correct! Wrong!

The system operates normally even with only one hydraulics system remaining

The amber FEEL DIFF PRESS light illuminates when the:

Flaps are not up (more than 5) and a hydraulic pressure imbalance is detected or one of the elevator feel pitot systems fails

Flaps are up and a pressure imbalance between hydraulic systems A & B is detected or if one of the elevator feel pitot systems fails

Flaps are not up and a hydraulic pressure imbalance is detected or one of the elevator feel pitot systems fails

Flaps are up or down and a hydraulic pressure imbalance is detected or if one of the elevator pitot systems fails. - No correct answer is provided.

Correct! Wrong!

During descent from altitude you need to decrease your aispeed by using your speed brakes. What is the correct position of the SPEED BRAKE LEVER.

ARMED

FLIGHT DETENT

Any intermediate position.

Correct! Wrong!

What is the correct flap setting for a jammed stabilizer landing?

30 or 40

Correct! Wrong!

The number of slats located on each wing are:

Correct! Wrong!

Yaw damper inputs (main or standby) can be overriden:

By rudder pedal inputs but not trim inputs

Only when the yaw damper switch is off

By trim inputs but not rudder pedal inputs

By either trim or rudder pedal inputs.

Correct! Wrong!

Extending the flaps to flaps 15 using ALTERNATE FLAPS takes approximately _______

4 minutes.

1 minute

30 seconds

2 minutes

Correct! Wrong!

The trailing edge flaps devices consist of double slotted flaps inboard outboard of each engine.

False

True

Correct! Wrong!

The Speed Trim System (STS) is a speed stability augmentation system designed to improve flight characteristics during operation with a low gross weight, aft center of gravity and high thrust when the autopilot is not engaged.

True

False

Correct! Wrong!

The STS monitors inputs of stabilizer position, thrust lever position, airspeed and vertical speed and then trims the stabilizer using the autopilot stabilizer trim.Remember that the SPEED TRIM FAIL amber light is often illuminated when you arrive at the aircraft. It is only due to the Inertial Vertical Speed Indicator which is not powered by the ADIRUs (IRS selectors OFF): the STS receives invalid inputs.

During flight with both hydraulic systems A & B inoperative:

The autoslat system is still functional through the operation of the PTU

The standby hydraulic system operates the flaps flaps system normally

The standby hydraulic system operates the trailing edge flaps normally

Trim is available for the stabilizer and rudder only. Aileron trim is inoperative with the autopilots disengaged.

Correct! Wrong!

The FEEL DIFF PRESS light indicates:

A loss of pressure in the elvator feel computer.

An excessive temperature in the elevator feel computer

An excessive differential pressure in the elevator feel computer.

A data loss in the elevator feel computer.

Correct! Wrong!

Excessive differential pressure can be caused by erroneous activation of the Elevator Feel Shift module.

With the loss of hydraulic system B, (system A operating normally):

Main yaw damper functions are available as long as hydraulic system A is providing normal pressure and the yaw damper switch is ON.

Standby yaw damper functions are available as long as hydraulic system A is providing normal pressure and the yaw damper switch is ON

Standby yaw damper functions are available if the FLT CONTROL B switch is placed to STBY RUD and the YAW DAMPER switch is reset to ON

Main & standby yaw damper functions are lost

Correct! Wrong!

If wheel spinup is not detected on landing with the speed brake armed the flight spoilers will deploy automatically :

When the ground spoilers deploy

Only when the RIGHT main landing gear strut compresses

When the air/ground system senses the ground mode (any strut compresses)

Flight spoilers do not deploy on landing, only ground spoilers deploy.

Correct! Wrong!

Speed Trim Failure (SPEED TRIM FAIL) Light - If illuminated (amber) this indicates a:

Partial failure of the speed trim system if the MASTER CAUTION can be reset.

Failure of the speed trim system

Failure of the speed trim system but also indicates failure of the elevator system if the MASTER WARNING cannot be reset.

Failure of the speed trim system but also indicates a failure of a single FCC channel when MASTER CAUTION light recall is activated and light extinguishes when Master Caution System is reset.

Correct! Wrong!

The speedbrake lever will move forward and all spoilers will retract if either thrust lever is advanced after landing.

False.

True

Correct! Wrong!

The SPEED BRAKE DO NOT ARM light indicates that the speedbrake is not usable.

False

True

Correct! Wrong!

Elevator Feel provides simulated aero forces using airspeed from elevator pitot & stabilizer position.

True

False

Correct! Wrong!

The feel is transmitted to the control columns by the elevator feel & centering unit.

The trailing edge flaps are at 15 units. The correct indication on the aft overhead panel for the leading edge devices is:

LE slats EXT lights and LE flaps FULL EXT lights illuminated.

All LE devices FULL EXT lights illuminated

All LE devices EXT lights illuminated

All amber TRANSIT lights illuminated

Correct! Wrong!

Leading Edge devices are normally operated by ______

Standby Hydraulic system.

Hydraulic System A

Hydraulic System B

Hydraulic Systems A & B

Correct! Wrong!

The flight control computers use Mach Information from the _____ to compute a Mach trim actuator position.

Mach/Airspeed Indicator and thrust levers position

ADIRU

Airspeed Indicator and any thrust lever position.

Airspeed Indicator

Correct! Wrong!

If the spoilers become jammed:

The ALT spoiler system is selected

The first officer’s control wheel operates the spoilers and ailerons

The captain’s control wheel operates the ailerons

The first officer’s control wheel operates the ailerons

Correct! Wrong!

The Speed Trim System (STS) operates most frequently during takeoffs & go-arounds. Conditions for speed trim operation are:

Airspeed between 100 KIAS and Mach 0.68, 15 seconds after takeoff, 5 seconds following release of trim switches, N1 above 60%, sensing of trim requirement

Airspeed between 100 KIAS and Mach 0.68, 10 seconds after takeoff, 5 seconds following release of trim switches, N1 above 40%, sensing of trim requirement

Airspeed between 100 KIAS and Mach 0.68, 10 seconds after takeoff, 5 seconds following release of trim switches, N1 above 40%, autopilot not engaged, sensing of trim requirement

Airspeed between 100 KIAS and Mach 0.68, 10 seconds after takeoff, 5 seconds following release of trim switches, N1 above 60%, autopilot not engaged, sensing of trim requirement

Correct! Wrong!

? With a loss of both system A & B, the elevator FEEL DIFF PRESS light will illuminate:

False

True

Correct! Wrong!

During the ALTERNATE FLAPS OPERATION procedure, the flight crew should plan a Flaps 15 landing. After arming the ALTERNATE FLAPS MASTER SWITCH (230 kt max), the flight crew set the flaps to desired flap position and extend flaps on maneuvering speed schedule. The LE FLAPS TRANSIT light will remain illuminates until the flaps approach the:

Flaps 1 position

Flaps 5 position

Flaps 10 position

Flaps 15 position.

Correct! Wrong!

In addition to Hydraulic System A & B, the rudder can also be powered by the Standby Hydraulic System through the:

System B Standby Rudder Power Control Unit

Standby Rudder Power Control Unit

System A Standby Rudder Power Control Unit

Main Rudder Power Control Unit

Correct! Wrong!

Concerning Mach Trim operation, FCCs use Mach information from the ADC / ADIRU, to compute a Mach trim actuator position whih repositions the elevator feel & centering unit, which adjusts the control column neutral position (column will not move).

False

True

Correct! Wrong!

The column will move

If the flight crew activates the FLT CONTROL switch Overhead panel to STBY RUD, it activates the:

Standby hydraulic system pump and closes flight control shutoff valve, isolating ailerons and elevators.

Standby hydraulic system pump and opens the standby rudder shutoff valve to pressurize standby rudder power control unit.

Standby hydraulic systemp pump.

Standby hydraulic system pump and closes the standby rudder shutoff valve

Correct! Wrong!

The Flap/Slat Electronics Unit (FSEU) provides:

Uncommanded motion protection for LE devices and TE flaps.

All statements are correct.

LE skew detection for slats 2 through 7 except during autoslat operation

TE asymetry protection by removing hydraulic pressure to the TE flaps if an asymetry is detected

Correct! Wrong!

What is number of ground spoilers on each wing?

Correct! Wrong!

Dual AILERON trim switches, located on the aft electronic panel, must be pushed simultaneously to command trim changes. The trim electrically repositions the aileron feel and centering unit, which causes the control wheel to rotate and redefines the aileron neutral position.

True

False.

Correct! Wrong!

Roll control is provided by the ailerons, assisted by the _____

Flight spoilers or ground spoilers (depending on speed)

Flight spoilers & ground spoilers

Ground spoilers

Flight spoilers

Correct! Wrong!

Landing flap 40 selected and in position. An IAS of 178kts is flown due to a highwind gust. Would you expect:

Flaps to retract to 15.

Flaps to retract to 30.

Flaps to remain in the current configuration.

Flaps to retract to 25.

Correct! Wrong!

! When the flaps are set at 40, the TE flaps:- retract to 30 if airspeed exceeds 163 knots- re-extend when airspeed is reduced below 158 knots.When the flaps are set at 30, the TE flaps:- retract to 25 if the airspeed exceeds 176 knots- re-extend when airspeed is reduced below 171 knots.

The flight spoilers rise on the wing with up aileron and remain faired on the wing with down aileron. When the control wheel is displaced more than approximately ____ degrees, spoiler deflection is initiated.

6,5

Correct! Wrong!

The amber LE FLAPS TRANSIT light:

Is inhibited during Autoslat operation inflight

Provides TE Flaps asymetry protection.

Indicates all LE Devices are fully extended

Indicates LE Slats are fully extended

Correct! Wrong!

Loss of Hydraulic System B pressure does not cause illumination of the amber YAW DAMPER light or yaw damper disengagement.

False.

True.

Correct! Wrong!

The flap load relief system is operational at:

Flaps 15, 30 & 40

Flaps 30 & 40

Flaps 40 only.

All flap settings

Correct! Wrong!

If the SPEEDBRAKES EXTENDED light is illuminated in flight. It indicates:

The speed brake lever is beyond the ARMED position with either the TE flaps extended more than Flaps 1 or the Radio altitude is less than 800 ft

The speed brake lever is beyond the ARMED position with either the TE flaps extended more than Flaps 15 or the Radio altitude is less than 2500 ft

The speed brake lever is beyond the ARMED position with either the TE flaps extended more than Flaps 5 or the Radio altitude is less than 500 ft

The speed brake lever is beyond the ARMED position with either the TE flaps extended more than Flaps 10 or the Radio altitude is less than 800 ft

Correct! Wrong!

The Autoslat system:

Provides for slat deployment above VMO/MMO

Drives the slats to FULL EXTEND when TE Flaps 1 through 5 are selected and the airplane approaches a stall

Is normally powered by Hydraulic System A

Is normally powered by Transfer Bus No.2

Correct! Wrong!

At what flap setting(s) should the leading edge slats be in the FULL EXTEND position?

1 to 5

5 to 40.

Greater than 5

Correct! Wrong!

Main electric trim has 2 speed modes : high & low speed.

True.

Correct! Wrong!

Elevator system feel is provided by the elevator feel computer. This computer receives inputs of:

Elevator balance tabs position

Only System A hydraulic pressure

Airspeed & stabilzer position.

Altitude & elevator position

Correct! Wrong!

During a normal landing, flight spoilers & ground spoilers will always extend simultaneously.

True

False.

Correct! Wrong!

What is the maximum flap extension altitude?

17 000 feet

10 000 feet

23 000 feet

20 000 feet

Correct! Wrong!

Mach Trim system corrects for Mach tuck by moving stabilizer up.

True.

False.

Correct! Wrong!

It moves elevators up (not the stabilizer)

During a steady right-handed turn on the ground, correct indications of the Yaw Damper indicator would be?

Steady full scale left deflection.

Steady in the center position.

Steady full scale right deflection

Correct! Wrong!

The primary flight controls consist of rudder, ailerons and ______

Elevators

Flaps

Speedbrakes

Spoilers

Correct! Wrong!

The Power Transfer Unit provides an alternate source of power for the Autoslat System if:

Hydraulic System A engine driven pump is inoperative

The Alternate Flaps Position Switch is momentarily held down

A loss of pressure from the Hydraulic System B engine pump is sensed.

A loss of Hydraulic System A pressure is sensed

Correct! Wrong!

The airspeed range for trim operation is:

100-300 KIAS

158-300 KIAS

100 KIAS - Mach 0.50

100 KIAS - Mach 0.615

Correct! Wrong!

If the flight crew selects the ALTERNATE FLAPS to the ARM position:

Standby pump is armed while the Trailing Edge flap bypass valve is de-energized.

Trailing Edge flap bypass valve closes, standby pump activates and ALTERNATE FLAPS position switch is armed

Standby pump is armed while the Trailing Edge flap bypass valve is energized.

Trailing Edge flap bypass valve closes and standby pump activates.

Correct! Wrong!

Why are mechanical gates installed on the flap selector unit.

To hinder flap movement beyond F15 until gear down is selected.

Prevent flap movement to UP position when speed is too low.

Prevent flap movement to UP position

To prevent inadvertent flap lever movement beyond F1 and F15 during G/A

Correct! Wrong!

The elevator transfer mechanism allows:

The elevator feel & centering unit to transfer proper aerodynamic forces to the control columns

Forces from either control column to be transferred to the stabilizer.

The control column to be physically separated in the event of an elevator jam.

The elevator feel and centering unit to transfer the source of power for elevator actuators to hydraulic systems A or B, depending upon which is producing higher pressure.

Correct! Wrong!

What is the number of flight spoilers located on each wing?

Correct! Wrong!

In the event of hydraulic Systems A & B fail, ailerons, elevators, and rudder can be operated with the Standby system.

True

False

Correct! Wrong!

What do the MACH TRIM FAIL, SPEED TRIM FAIL & AUTO SLAT FAIL lights have in common? + All of the above.

Also illuminates the Master Caution & FLT CONT annunciator lights.

Will illuminate if both system computers fail.

Will illuminate during Master Caution Recall if only one computer has failed.

All statements are correct.

Correct! Wrong!

A Mach Trim system provides speed stability at the higher Mach numbers.Mach trim is automatically accomplished above:

Mach 0.615

Mach 0.655

Mach 0.50

Mach 0.70

Correct! Wrong!

Quiz

Boeing B737NG - Flight controls

During an ALL FLAPS UP LANDING, the speed to be maintained is:

The ALTERNATE FLAPS Master Switch:

To operate the Feel system, the Elevator Feel Computer uses:

The amber FEEL DIFF PRESS light illuminates when the:

During descent from altitude you need to decrease your aispeed by using your speed brakes. What is the correct position of the SPEED BRAKE LEVER.

What is the correct flap setting for a jammed stabilizer landing?

The number of slats located on each wing are:

Yaw damper inputs (main or standby) can be overriden:

Extending the flaps to flaps 15 using ALTERNATE FLAPS takes approximately _______

The trailing edge flaps devices consist of double slotted flaps inboard outboard of each engine.

The Speed Trim System (STS) is a speed stability augmentation system designed to improve flight characteristics during operation with a low gross weight, aft center of gravity and high thrust when the autopilot is not engaged.

During flight with both hydraulic systems A & B inoperative:

The FEEL DIFF PRESS light indicates:

With the loss of hydraulic system B, (system A operating normally):

If wheel spinup is not detected on landing with the speed brake armed the flight spoilers will deploy automatically :

Speed Trim Failure (SPEED TRIM FAIL) Light - If illuminated (amber) this indicates a:

The speedbrake lever will move forward and all spoilers will retract if either thrust lever is advanced after landing.

The SPEED BRAKE DO NOT ARM light indicates that the speedbrake is not usable.

Elevator Feel provides simulated aero forces using airspeed from elevator pitot & stabilizer position.

The trailing edge flaps are at 15 units. The correct indication on the aft overhead panel for the leading edge devices is:

Leading Edge devices are normally operated by ______

The flight control computers use Mach Information from the _____ to compute a Mach trim actuator position.

If the spoilers become jammed:

The Speed Trim System (STS) operates most frequently during takeoffs & go-arounds. Conditions for speed trim operation are:

? With a loss of both system A & B, the elevator FEEL DIFF PRESS light will illuminate:

In addition to Hydraulic System A & B, the rudder can also be powered by the Standby Hydraulic System through the:

Concerning Mach Trim operation, FCCs use Mach information from the ADC / ADIRU, to compute a Mach trim actuator position whih repositions the elevator feel & centering unit, which adjusts the control column neutral position (column will not move).

If the flight crew activates the FLT CONTROL switch Overhead panel to STBY RUD, it activates the:

The Flap/Slat Electronics Unit (FSEU) provides:

What is number of ground spoilers on each wing?

Dual AILERON trim switches, located on the aft electronic panel, must be pushed simultaneously to command trim changes. The trim electrically repositions the aileron feel and centering unit, which causes the control wheel to rotate and redefines the aileron neutral position.

Roll control is provided by the ailerons, assisted by the _____

Landing flap 40 selected and in position. An IAS of 178kts is flown due to a highwind gust. Would you expect:

The flight spoilers rise on the wing with up aileron and remain faired on the wing with down aileron. When the control wheel is displaced more than approximately ____ degrees, spoiler deflection is initiated.

The amber LE FLAPS TRANSIT light:

Loss of Hydraulic System B pressure does not cause illumination of the amber YAW DAMPER light or yaw damper disengagement.

The flap load relief system is operational at:

If the SPEEDBRAKES EXTENDED light is illuminated in flight. It indicates:

The Autoslat system:

At what flap setting(s) should the leading edge slats be in the FULL EXTEND position?

Main electric trim has 2 speed modes : high & low speed.

Elevator system feel is provided by the elevator feel computer. This computer receives inputs of:

During a normal landing, flight spoilers & ground spoilers will always extend simultaneously.

What is the maximum flap extension altitude?

Mach Trim system corrects for Mach tuck by moving stabilizer up.

During a steady right-handed turn on the ground, correct indications of the Yaw Damper indicator would be?

The primary flight controls consist of rudder, ailerons and ______

The Power Transfer Unit provides an alternate source of power for the Autoslat System if:

The airspeed range for trim operation is:

If the flight crew selects the ALTERNATE FLAPS to the ARM position:

Why are mechanical gates installed on the flap selector unit.

The elevator transfer mechanism allows:

What is the number of flight spoilers located on each wing?

In the event of hydraulic Systems A & B fail, ailerons, elevators, and rudder can be operated with the Standby system.

What do the MACH TRIM FAIL, SPEED TRIM FAIL & AUTO SLAT FAIL lights have in common? + All of the above.

A Mach Trim system provides speed stability at the higher Mach numbers.Mach trim is automatically accomplished above: